PIPE & CABLE LOCATORS SERIES 2              

Link to C-SCOPE   

 

All C-SCOPE HIGH PERFORMANCE SERIES 2 DIGITAL LOCATING MODELS FEATURE:

 

  • Simultaneous frequencies (33KHz+131KHz)
  • Improved Signal Detection
  • Fast Meter response
  • Depth Measurement
  • Automatic Self test
  • Data Logging (optional)
  • Unique Full Frequency AllScan
  • USB Data Transfer
  • No Periodic Calibration
  • Three Year Warranty (conditions apply)
DXL-2_TDs.jpg

NEW DXL 2 fully digital Cable Avoidance Tool

 

 

The DXL2 is a new ultra modern and high performance Cable Avoidance Tool with Depth Measurement that has been designed to set a new benchmark in excavating safety as well as still delivering all the advantages and familiar operating practices associated with the original C.Scope product range. The DXL2 is loaded with new features which enable operators to find more buried utilities by delivering improved levels of performance and helping to reduce the effects of human error.

The DXL2 Cable Avoidance Tool is driven by powerful Digital Signal Processor Technology. Advanced software programming enables the new products to provide outstanding detection performance even when locating in the most difficult areas. The DXL2 delivers improved signal detection sensitivity and better noise rejection so the locator is capable of detecting the smallest of signals even in areas of high service density and electrical noise. The addition of the new simultaneous dual 33+131kHz frequency will assist in the detection of smaller buried pipes and cables such as telecoms, sheathed fibre optics and street lighting spurs.

The DXL2 has four detection modes to select from each mode providing its own specific advantages:

POWER mode identifies buried electricity cables by detecting the mains frequency signal travelling along the cable itself, when current is being drawn.

RADIO mode detects re-radiated ‘Radio’ type signals that are often present on metal pipes and cables.

GENERATOR mode is used to detect the 33+131kHz signal applied to a  pipe or cable by a SGA2 or SGV2 Signal Generator. The combination of a high frequency with the 33kHz signal enables small diameter cables to be located more easily. The Generator mode should also be used when detecting the signal from a C.Scope Sonde when tracing in non metallic pipes such as plastic and clay.

ALLSCAN mode detects ALL frequencies of signal from the lowest of the Power signals right up to and including 33kHz. This mode can detect unusual signals appearing in the frequency gaps between conventional Power, Radio and Generator modes and is invaluable as a ‘final check’ before excavation.

Human error can be a contributory factor associated with cable strikes. To address this issue, intelligent features such as an Automatic Daily Self Test function and a dynamic Swing Sensor help ensure that best working practices are adhered to and being applied on-site. The Data Logging option can also provide an invaluable insight into working practices and help to identify potential training requirements.

The new DXL2 offers a significant step forward in the quest to reduce the day-to-day risk of cable strikes.

MAINTENANCE & CALIBRATION
As with ALL C.Scope digital Cable Avoidance Tools - no yearly calibration checks are required.

MXL-2_TD_s.jpg

NEW MXL2 fully digital Multi - Frequency

 

Cable Avoidance Tool

 

 

The new C.Scope MXL2 Locator is a high performance Locator specifically designed to detect, identify and trace specific buried pipes and cables reliably and accurately, even in the most congested areas. It is especially useful for those that wish to identify the route of a particular pipe or cable such as utility technicians or maintenance engineers.

The new MXL2 from C.Scope has been designed to set a new benchmark in excavating safety as well as still delivering all the advantages and familiar operating practices associated with the original MXL. The MXL2 is loaded with new features which enable operators to find more buried utilities by delivering improved levels of performance and helping to reduce the effects of human error.

The MXL2 Pipe and Cable Locator is driven by powerful Digital Signal Processor Technology. Advanced software programming enables the MXL2 to attain performance levels normally only associated with high end pipe and cable surveying instruments. The MXL2 delivers improved signal detection sensitivity and better noise rejection so the locator is capable of detecting the smallest of signals even in areas of high service density and electrical noise.

The new simultaneous 33+131kHz signal detection give the MXL2 even greater tracing and detecting capabilities. The 33+131kHz signal detection is ideal for general utility location and detects more smaller buried pipes and cables such as telecoms, sheathed fibre optics and street lighting spurs, 8kHz traces deeper and over longer distances and the ultra low frequency 512/640Hz signal is invaluable for specialist tracing.

FOUR DETECTION MODES
The MXL2 has four detection modes to select from. Each mode provides specific advantages:

POWER MODE identifies buried electricity cables by detecting the mains frequency signal travelling along the cable itself, when current is being drawn.

RADIO MODE detects re-radiated ‘Radio’ type signals that are often present on metal pipes and cables.

TRANSMITTER mode is used to detect the signal applied to a metal pipe or cable by a C.Scope MXT2 Transmitter. The ability to select from a simultaneous 33kHz+131kHz signal as well as 8kHz and 512/640Hz signals gives the operator more versatility to detect and trace utilities. This mode is also used for detecting the signal from a C.Scope Sonde or Plastic Pipe Tracer when tracing in non metallic pipes such as sewers, drains or cable ducts.

ALLSCAN MODE detects ALL frequencies of signal from the lowest of the Power signals right up to and including 33kHz. This mode can detect unusual signals appearing in the frequency gaps between conventional Power, Radio and Transmitter modes and is invaluable as a ‘final check’ before excavation.

DEPTH MEASUREMENT

When used with an MXT2 Transmitter the depth of buried pipes, cables and sondes can be indicated at the push of a button.

SIGNAL CURRENT MEASUREMENT

A further development from Depth Measurement. The MXL2 can monitor the true strength of the MXT2 Transmitter signal applied to a buried service irrespective of its depth. This is ideal for identifying the layout of a pipe or cable network.

Human error can also be a contributory factor associated with cable strikes. To address this issue, intelligent features such as an Automatic Daily Self Test function and a dynamic Swing Sensor help ensure that best working practices are adhered to and being applied on-site. The Data Logging option can also provide an invaluable insight into working practices and help to identify potential training requirements.

MAINTENANCE & CALIBRATION

As with ALL C.Scope digital Cable Avoidance Tools - no yearly calibration checks are required.

SGA2-SGV2.jpg

NEW SGA 2 / SGV 2 Transmitters

 

Suits DXL 2 / CXL 2 Cable Avoidance Tools

 

 

The new C.Scope SGA2 and SGV2 Signal Generators are a vital partner for the C.Scope CXL2 or DXL2 Cable Avoidance Tools and significantly increase the number of buried services that can be found. The addition of a new combined 33kHz+131kHz signal further increases the number of buried services that can be energised and detected.

The new SGA2 and SGV2 Signal Generators from C.Scope have been designed to set a new benchmark in excavating safety as well as still delivering all the advantages and familiar operating practices associated with the original C.Scope product range. The new products are loaded with new features which enable operators to find more buried utilities by delivering improved levels of performance. Using the CXL2/DXL2 with the new SGA2/SGV2 maximises the full performance capabilities of the new products.

The new SGA2 and SGV2 have a class leading One watt Power output which helps to get a detectable signal onto deeper and less conducting pipes and cables for complex locate tasks and provides longer distance tracing capability. The SGV2 Signal Generator has four position power level adjustment so the operator can control how much power to use and when. The SGA2 Signal Generator enables you to toggle between a high & low setting.

Both the SGA2 and SGV2 offer the choice of a Pulsed or Continuous signal output. Switch to the Pulsed Mode, at the push of a button in high interference situations and keep on tracing.

The SGA2 and SGV2 Signal Generators have a clear audible signal output to indicate when they are in operation and also feature an inbuilt mute control. The SGV2 has a multi-segment Liquid Crystal Display that provides clear information about the functions selected. The display also shows the all important battery condition so you always know exactly how much battery  life you have at your disposal.

The new products offer a significant step forward in the quest to reduce the day-to-day risk of cable strikes.

MAINTENANCE & CALIBRATION

As with ALL C.Scope digital Cable Avoidance Tools - no yearly calibration checks are required.

MXT-2_TD_small.jpg

NEW MXT2 Signal Generator (4 Active frequencies)

 

Suits MXL2 Cable Avoidance Tool.

 

 

The new C.Scope MXT2 Transmitter is the ideal partner for the MXL2 Locator. The range of operating frequencies and adjustable power output is designed to make the MXL2 and MXT2 an extremely versatile combination for pipe and cable location that can tackle many varied locating tasks.

The MXT2 Transmitter from C.Scope has been designed to set a new performance benchmark. It is loaded with new features designed specifically to help detect, trace and identify specific buried pipes and cables more effectively, reliably and accurately even in areas of high service density as well as still delivering all the advantages and familiar operating practices associated with the original MXT.

MULTI FREQUENCY

The MXT2 Transmitter offers a choice of frequencies to suit any job. Use the simultaneous 33+13kHz signal detection for general utility applications and detecting smaller buried pipes and cables such as telecoms, sheathed fibre optics and street lighting spurs, 8kHz traces deeper and over longer distances and the ultra low frequency 512/640Hz signal is invaluable for specialist tracing.

The MXT2 has a powerful One watt Power output which helps to get a detectable signal onto deeper and less conducting pipes and cables for complex locate tasks and provides longer distance tracing capability. It has a four position power level adjustment so the operator can control how much  power to use and when.

The MXT2 has the choice of a Pulsed or Continuous signal output. Switch to the Pulsed Mode, at the push of a button  in high interference situations and keep on tracing.

The MXT2 also has a clear audible signal output to indicate when they are in operation and also feature an inbuilt mute control. A multi-segment Liquid Crystal Display provides clear information about the functions selected. The display also shows the all important battery condition.

The MXT2 when used with the new MXL2 offers a significant step forward in the quest to reduce the day-to-day risk of cable strikes.

MAINTENANCE & CALIBRATION

As with ALL C.Scope digital Cable Avoidance Tools - no yearly calibration checks are required.

 

                                                                                   

The C-SCOPE DXL2 & MXL2 range of

 

Cable Avoidance Tools.

 

 

Features

 

  • Power Mode.
  • Radio Mode.
  • Generator Mode - Combined 33+131kHz frequency detection improves utility detection.
  • All Scan Mode.
  • Accurate Depth Indication
  • Automatic Noise Rejection.
  • Dynamic Swing Sensor.
  • Automatic Daily Self Test.
  • Optional Data Logging of all Locator activity.
  • High resolution Liquid Crystal Display.
  • No Calibration checks required.
  • Three year Warranty (Conditions apply).


FOUR DETECTION MODES

The DXL2 has four detection modes to select from each mode providing it's own specific advantages:

 

POWER mode identifies buried electricity cables by detecting the mains frequency signal travelling along the cable itself, when current is being drawn.

 

RADIO mode detects re-radiated ?Radio? type signals that are often present on metal pipes and cables.

 

GENERATOR mode is used to detect the 33 + 131kHz signal applied to a a pipe or cable by a SGA2, SGV2 or MXT2 Signal Generator. The combination of a high frequency with the 33kHz signal enables small diameter cables to be located more easily. The Generator mode should also be used when detecting the signal from a C.Scope Sonde when tracing in non metallic pipes such as plastic and clay.

 

ALLSCAN mode detects ALL frequencies of signal from the lowest of the Power signals right up to and including 33kHz. This mode can detect unusual signals appearing in the frequency gaps between conventional Power, Radio and Generator modes and is invaluable as a ?final check? before excavation.

 

Human error can be a contributory factor associated with cable strikes. To address this issue, intelligent features such as an Automatic Daily Self Test function and a dynamic Swing Sensor help ensure that best working practices are adhered to and being applied on-site. The Data Logging option can also provide an invaluable insight into working practices and help to identify potential training requirements.

DEPTH MEASUREMENT

When used with an SGA2, SGV2 or MXT2 Signal Generator the depth of buried pipes, cables and sondes can be indicated at the push of a button.

DYNAMIC SWING SENSOR

The DXL2/MXL2 recivers will sound a single tone to alert the operator that the Locator is being swung excessively. This will help operators maintain correct technique during every search.

AUTOMATIC DAILY SELF TEST (ADST)

The DXL2/MXL2 has comprehensive self test circuitry. ADST tests the Locator including the receiving aerials for correct performance each day when it is first switched on. As well as storing the test result for later reference if needed, the ADST gives the operator confidence that the Locator is working to its optimum before use at the start of each day.

DATA LOGGING

The DXL2/MXL2 is available with or without the option of Data Logging. The Data Logging versions will automatically record how and when it is being used. Over 12months of data (in normal use) can be stored before being overwritten. A full audit trail is kept of all activity so that it is possible to see when the Cable Avoidance Tool passed Self Tests, which Modes have been used, when, and for how long.

DATA LOG TRANSFER via USB

Data from the Data Logging versions can be transferred at any time to a PC for analysis via the data connection socket in the battery compartment.

 

DATA LOG ANALYSIS

C.Scope?s FREE to download XL2 Edition PC Toolkit allows manipulation of the stored data-logs into charts and graphs that illustrate all aspects of the use. The data can be used to show correct usage in addition to assisting the identification of actual operator behaviour and any training requirements.

LCD CLEAR DIGITAL DISPLAY

The recievers have a large, clear and easy to read backlit LCD mounted behind a protective polycarbonate lens. The display indicates detection mode, signal peak level, depth, signal strength and battery condition. It also displays the Automatic Daily Self Test results.

FINGERTIP CONTROLS

The receivers ergonomic controls offer easy singlehanded sensitivity adjustments and mode selection.

DETACHABLE SPEAKER

The speaker can be easily detached for use in noisy work environments.

DATA CONNECTION

The DXL2/MXL2 features a data connection socket for transferring data to a PC using the C.Scope XL2 Edition PC Toolkit.

ROBUST AND DURABLE CONSTRUCTION

The receivers twin wall construction is robust and durable. It also provides IP65 standard protection against dust and water ingress.

CALIBRATION

The DXL2/MXL2 does not require periodic re-calibration helping to reduce running costs and downtime.

SYSTEM VALIDATION CERTIFICATION

The C.Scope XL2 Edition PC Toolkit allows owners to print a System Validation Certificate by connecting the Cable Avoidance Tool to a PC via USB. The results are generated from the ADST results that are stored on the Cable Avoidance Tool.

SERVICE

Full warranty, service and maintenance is available through Altech Distributors here in Australia.

WARRANTY

All C-SCOPE Products come with a three year Warranty (conditions apply).

 

Services

PIPE & CABLE LOCATOR:

Repair & Calibration - Function Check - Training

Repair & Calibration

Altech Distributors is the approved C.Scope service centre in Australia for the maintenance, repair and calibration of C.Scope Pipe and Cable Locators, Receivers, Signal Generators, Transmitters and Accessories.

 

The accuracy of electronic components used in all instruments naturally drifts over time. Therefore, it is necessary to calibrate instruments at regular intervals as defined by the manufacturer. Calibration improves the measurement performance of an instrument. Benefits of maintaining properly calibrated equipment include reduced measurement errors and consistency between measurements. To help you meet your calibration needs, Altech Distributors provides calibration support and services that include manual calibration procedures, and use of a factory built and calibrated function checkers, designed specifically for their products.

 

Altech Distributors strives to achieve the highest level of quality in every product it sells. Before a product leaves our factory, it undergoes testing and inspection.

 

Latest Series C-SCOPE Locators (Grey Series)

Following the successful introduction of a new range of equipment featuring a digital processing core - we can confirm that these new products do not require annual recalibration.

 

The following products DO NOT require annual calibration:

  • C.Scope CXL Cable Avoidance Tool (part number ZCSCXLCAT-33G)
  • C.Scope DXL Cable Avoidance Tool (part number ZCSDXLCAT-33G)
  • C.Scope MXL Locators (part numbers ZCSMXL-33-8-640 and ZCSMXL-33-8-512) 
  • C.Scope SGA Grey Signal Generator (part number ZCSSGA-33G)
  • C.Scope One Watt SGV Signal Generator (part number ZCSSGV1-33G) 
  • C.Scope MXT Transmitters (part numbers ZCSMXT-33-8-640 and ZCSMXT-33-8-512).


We continue to recommend that the following C.Scope products DO require calibration 
every 12 months:

  • C.Scope Cable Avoidance Tool (part number ZCSCAT-33), 
  • C.Scope Cable Avoidance Tool XD with depth measuring (part number ZCSCATXD-33) 
  • C.Scope SGA Signal Generator (part number ZCSSGA-33)
  • C.Scope SGV Signal Generator (part number ZCSSGV-33)
  • C.Scope Function Checker (part number YIRFC).


Put simply, all C.Scope Locators and Signal Generators with a grey case DO NOT require annual recalibration and all C.Scope Locators and Signal Generators with a black case DO require annual recalibration.

C-Scope Locator Function Checks

It is recommended that the operation of the C.Scope Cable Avoidance Tool and Signal Generator is checked before use.

 

These checks DO NOT guarantee full system performance. The Cable Avoidance Tool and Signal Generator should be returned to the manufacturer or an approved agent for recalibration every 12 months.

 

Battery Condition

Check by depressing the On/Off switch beneath the handle. The display will show at least one solid segment if the batteries are ok. Ensure power on tone is heard.

 

Power Mode

Select Power Mode. Set Sensitivity fully clockwise and point the body of the C.Scope Cable Avoidance Tool at a fluorescent light from a distance of 1m. Switch the light on. A loud tone should be heard and the display should read greater than 50% full scale. Reducing the sensitivity should cause the displayed reading to reduce and the tone to cut out.

 

Radio Mode

Select Radio Mode. Set the Sensitivity fully clockwise and, from a distance of less than 0.25m, point the unit at a metal conductor of length greater than 100m (for example a pipe or cable). A warbling tone should be heard. The display should read greater than 50% full scale.

 

Generator Mode

Locate an outdoor test area that is free from extraneous fields resulting from overhead and underground cables. The area should also not be near fences, steel framed buildings, or on reinforced concrete as the signal will be reduced.

Place the Signal Generator on the ground in the normal orientation and switch on - a tone should be heard. Set to Continuous and ensure highest output power is selected.

 

With the C.Scope Cable Avoidance Tool in the orientation shown, and Sensitivity rotated.

 

CS14.jpg - large

 

Depth Measurement Checks

An area free of services, metal structures, etc should be chosen (beware of reinforced car parks). A search with the C.Scope Cable Avoidance Tool in all 3 modes will help confirm the absence of other services. An insulated cable or wire 20m+ (not supplied) is laid out on the ground surface and the far end connected to a ground stake and earthed. The near end is connected to the red Connected Mode lead.

 

The black ground Lead should be laid at right angles to the 20m wire and earthed at the far end with a ground stake. The plug should be inserted in the connector on the Signal Generator.

The Signal Generator is turned on with lowest power, and continuous mode selected. The C.Scope Cable Avoidance Tool should then be held vertically above the longer wire, approximately midway along it, ie. 10m from the Signal Generator.

 

The depth can then be measured. It is best to make a few readings at different depths. (Beware - metal step ladders affect the accuracy!)

 

CS15.gif - large

 

Signel Generator Function Checks

Battery Condition

Select Continuous. Good batteries will be shown by a loud clear audio tone. Bad batteries give an interrupted audio tone. On the SG-V the display will show at least one solid segment if the batteries are ok.

 

Induced Mode

This can only be checked in conjunction with a C.Scope Avoidance Tool as described in Locators Function Check.

If the unit does not meet the results required, repeat the test with another C.Scope Cable Avoidance Tool to determine whether the Signal Generator is suspect.

 

Connected Mode

Set the minimum output level, insert the connection lead and the long earth lead and then connect the red lead to the long earth lead to create a short circuit. The pitch should change to a low tone.

 

The leads should be arranged to create an open loop on the ground of approximately 1m diameter. Check that a signal can be detected by the Cable Avoidance Tool (in Generator Mode) when pointed closely at the loop.

C-Scope Training

Altech offers a range of training for your operators and training personnel and is available on your site, or at our Office. Training is carried out by a qualified instructor and each trainee receives a certificate to confirm they have received the training.

 

Aim

To ensure candidates understand the need to use location equipment and to instruct them to operate pipe and cable locators in an accurate and safe manner.

 

Duration

Typically the full course duration is 4 hours. Refresher course being 2.5 Hours

 

Candidate Numbers

Up to 10 candidates can be trained in a single course.

 

Venue

  • Our Training Facility:
    • We can provide training at our office in Lilydale Victoria.
  • Customers Address:
    • No special facilities are needed apart from a suitable room to allow the theory to be presented without disturbance. Access to an area where there are buried services is also required. (Street with buried telecommunication cables,  power cables, water and/or gas services.

 

 

Certificates

Upon completion of the course each trainee will be provided  with a  certificate to confirm they have completed the course.

 

Content

The course consists of theoretical and practical training involving hands on use of the actual locators to detect and trace the route of buried services. The actual agenda is summarised below:

 

Introduction

This will cover the different types of buried services that exist, current legislation concerning detecting buried services, the safety implications of not using a locator plus ancillary locating work to be done (use of “Dial Before You Dig” cable plans, and observation of street fixtures etc.)
THEORY: A general overview of how locators work followed by a step by step explanation of exactly what can and cannot be detected on the different modes. Typically use of the Cable Avoidance Tool alone is covered first followed by use of a Signal Generator. Accessories that are appropriate to the work that the candidates carry out will be included. Correct maintenance and care of the equipment is also discussed.

 

Practical

Candidates are shown the correct way to handle and operate the equipment on all modes before being given the opportunity to gain hands-on experience themselves. Any bad habits will be quickly picked up and corrected. Time is spent practising the techniques of detecting signals, pinpointing their source and then finally tracing the route of the service. A Signal Generator and the relevant accessories will also be used.

 

Special Requirements

Our training is derived from experience in using locators in a diverse range of situations over many years and we bring this experience to the training course. We always seek to make our courses specific to the type of work that the candidates are involved with and encourage candidates to participation in discussion on the subject of locating throughout the course. The training is carried out in a friendly, relaxed manner and the theoretical content is covered in simple, easy to understand terms.

 

Cost

 

Full Course:

  • Your Site:
  • Our Office:

Refresher Course:

  • Your Site:
  • Our Site:

 

For more information on our training services please contact us.