The MTRAK is a midi traceable rodder for tracing route of buried/underground smaller dia non metallic pipes (eg. - 25mm dia pipes or higher).

The MTRAK is based on a 5.5mm composite fiberglass rod with2x0.5mm tracer copper wires. The midi traceable duct rodder contain slip rings and spring loaded carbon brushes provided in a galvanized metal tube frame to enable usage of either of the copper tracer wires on an independent basis with the option to use both wires simultaneously. The base of the traceable rodder contains a terminal box that provides 2 individual terminal connections to the 2 inbuilt copper tracer wires of the traceable duct rodder.

After inserting the traceable rod into the pipe which is to be route traced, apply signal from the direct connection lead of a transmitter to a single terminal and connect the other lead of the transmitter to an earth stake which then excites the full length of the rodder to enable trace the buried pipe. If the output from the transmitter is applied to both terminals (direct connection lead attached to one terminal & earth lead to the other terminal) , the front leading tip of the rodder will be energized & will act very much like a sonde allowing the operator to localize the tip of the rodder & in turn any blockage points in the pipe. Use any Digital Pipe & cable locating receiver from above ground to trace the route of the Pipe.

Traceable Rods

Non-invasive detectable rods locate or map underground conduit or pipe without digging or trenching. Attach a standard Pipe and Cable Locator transmitter to the rod adaptor to locate to depths up to 2M. A copper wire inside the fibreglass inner core is energized with an electromagnetic signal that is detectable above ground through the use of the hand held signal receiver.

Available in 4.5mm, 6.7mm, 9mm and 11mm diameter rods, and variable lengths.

Traceable Rods

Non-invasive detectable rods locate or map underground conduit or pipe without digging or trenching. Attach a standard Pipe and Cable Locator transmitter to the rod adaptor to locate to depths up to 2M. A copper wire inside the fibreglass inner core is energized with an electromagnetic signal that is detectable above ground through the use of the hand held signal receiver.

Available in 4.5mm, 6mm, 8mm and 10mm diameter rods, and variable lengths

Traceable Rods

Non-invasive detectable rods locate or map underground conduit or pipe without digging or trenching. Attach a standard Pipe and Cable Locator transmitter to the rod adaptor to locate to depths up to 2M. A copper wire inside the fibreglass inner core is energized with an electromagnetic signal that is detectable above ground through the use of the hand held signal receiver.

Available in 4.5mm, 6mm, 8mm and 10mm diameter rods, and variable lengths

Plastic Pipe Tracers

The unique C.Scope Plastic Pipe Tracers are designed specifically to allow SMALL diameter, non-metallic pipes to be traced.

Developed as a result of requests from the British gas industry the C.Scope Plastic Pipe Tracers are the smallest diameter product on the market and can be successfully inserted into pipes when nothing else fits. Their unique construction gives unparalleled reliability and yet allows both 'line' tracing AND the all important 'end' tracing using the remarkable Sonde technology housed at the very tip of the Tracers.

Comes in 20 metre or 50 metre lengths.

Sondes

The C.Scope 8KHz & 33KHz Sonde is a small battery powered transmitter which, in typical use, would be screwed onto the end of a drain rod (a range of drain rod adaptors are available), and pushed down a pipe so that the pipe direction can be traced using the C.Scope locator set to 'Signal Generator Mode'. The location of a pipe blockage can be identified using this system, with enormous cost saving potential.

Mains Signal Injector

The Signal Injector is an accessory that allows the Signal Generator signal to be safely applied to an electrical system via a conventional 3-pin power socket. This signal will then be detectable on the buried supply cable outside the building.

Induction Clamp

The C.Scope Signal Clamp is a safe and straightforward way to apply the Generator signal to a cable or small pipe to enable precision tracing of this service.

Cover Locator / Metal Detector

The C.Scope CS880 is a neat solution to the problem of pinpointing the position of metal covers buried under earth, grass, concrete or bitumen.

C.SCOPE     CS4PI

Metal & Treasure Detector for Beach and Sand